|
Properties
|   |
|
Properties
| |
Properties
Levels found: 
Drop Down: Edit
Icon: 
Key Command-1: Alt + Enter
Key Command-2: Alt, E, R
Right Mouse Button: No
Description:
The “Properties” function has many different faces and changes depending on the
object or objects you may have selected.
The following is an explanation of all the different ways you might see and
use Properties. You may or may not have all the functions shown, it depends
on what level you have purchased. This function is one of the most
dynamic and changing functions within the software. The best thing to
remember is that this software and all of its levels is an object based software.
Each piece or pieces of a design is considered an object and the properties
(depending on the level purchased) can be changed or modified.
1. Applique Properties
2. Artwork Properties
6. Cross Stitch Properties
9. Manual Properties
10. Pull Compensation Properties
11. Run Properties
12. Steil Properties
13. Stitch Properties
14. Text Properties
15. Transform Properties
16. Underlay Properties
1. Manual properties (Figure Ref-P-06)
Lets you choose the color of your objects.
2. Run properties (Figure Ref-P-07)
You can set the:
a. Stitch Length (mm)
b. Type of stitch.
1. Standard
2. Two ply
3. Bean (three ply)
4. Motif (pattern box becomes active)
5. Symbol (pattern box becomes active)
3. Run properties (Figure Ref-P-08)
You can set the:
a. Fill Type:
1. Standard
2. Emboss
b. Pattern
c. Stitch Length (mm)
d. Density (pt)
4. Steil properties (Figure Ref-P-09)
You can set the:
a. Width
b. Angle
c. Inset%
d. Steil density
e. Corner type:
1. Square
2. Extended Figure Ref-P-09
5. Fill properties (Figure Ref-P-10)
You can set the:
a. Fill Type:
1. Standard
2. Emboss
3. Motif
b. Pattern
c. Stitch Length (mm)
d. Density (pt) Figure Ref-P-10
6. Applique properties (Figure Ref-P-11)
You can set the:
a. Type:
1. Satin
2. E-Stitch
3. Motif
4. Symbol
b. Applique width
c. Stitch length
d. Pattern length
e. Applique density
f. Corner type:
1. Square
2. Extended
g. Activation angle
7. Cross Stitch properties (Figure Ref-P-12)
You can set the:
a. Size
b. Overlap (pt)
c. Repeats
8. Artwork properties (Figure Ref-P-13)
You can set the:
a. Fill
9. Stitch properties (Figure Ref-P-14)
You can set the:
a. First Stitch (Control + Home)
b. Previous Path (Control + PgUp)
c. Previous stitch (Control + Left)
d. Next stitch (Control + Right)
e. Next Path (Control + PgDn)
f. Last Stitch (Control + End)
g. Color
h. Command
i. Offset X (pt)
j. Offset Y(pt)
10. Backdrop properties (Figure Ref-P-15)
You can set the:
a. Width (mm)
b. Height (mm)
c. Scale
d. Rotate
11. Underlay properties (Figure Ref-P-16)
You can set the:
a. Contour
b. Perpendicular
c. Lattice
d. Parallel
e. Zig-Zag
f. Full lattice
g. Density (pt)
h. Stitch length (mm)
i. Inset (mm)
j. Zig-Zag inset (mm)
12. Pull comp. properties (Figure Ref-P-17)
You can set the:
a. Type:
1. None
2. Percentage
3. Absolute
b. Value%
c. Max range (mm)
d. Absolute value (pt)
13. Column properties (Figure Ref-P-18)
You can set the:
a. Jagged type:
1. None
2. Both
3. First
4. Second
b. Jagged value (pt)
14. General properties (Figure Ref-P-19)
You can set the:
a. Connection End:
1. Sharp
2. Zig-Zag
3. Chiseled
4. Square
b. Chisel distance (mm)
c. Overlap lines
d. Gradient fill:
1. None
2. Linear increasing
3. Linear decreasing
4. Convex
5. Concave
e. Max density (pt)
f. Auto density
g. Short stitches
15. Command properties (Figure Ref-P-20)
You can set the:
a. Color
b. Start command:
1. Normal
2. Jump
3. Trim
4. Stop
5. Frame out
c. End command:
1. Normal
2. Jump
3. Trim
4. Stop
5. Frame out
d. Tie in:
1. None
2. Basic
3. Triangle
e. Tie off:
1. None
2. Basic
3. Triangle
f. Color Change (text command only)
1. None
2. Chars
3. Word
4. Line
g. Trim(text command only)
1. None
2. Chars
3. Word
4. Line
15. Transform properties (Figure Ref-P-21)
You can set the:
a. Width (mm)
b. Height (mm)
c. Maintain aspect ratio
d. Regenerate stitches
e. Rotate
f. Flip horizontal
g. Flip vertical Figure Ref-P-21
16. Text properties (Figure Ref-P-22)
You can set the:
a. Text input
b. Height (mm)
c. Space %
d. Line Spacing %
e. Reverse direction (circle only)
f. Optimize colors (for multi color fonts)
g. Font
h. Decor (Monogramming only)
i. Align:
1. Center
2. Left
3. Right
j. Frame:
1. Normal
2. Circle
3. Monogram(Monogram Master III only)
k. Text style
You can setup a text style and save it
for later use. It will save anything you
set in the properties command.
Related Resources:
3. Cross Stitch
4. Manual
5. Run
5. Satin
7. Steil